Numerical Modeling of Intracavity Spectral Broadening of Raman Fiber Lasers

Raman fiber lasers (RFLs) are efficient light sources at frequencies where no other comparable all-solid-state sources are available. Especially if fiber Bragg gratings (FBGs) with narrow bandwidths are used, the bandwidth of the Stokes light is strongly broadened by Kerr nonlinearities like four-wave mixing (FWM), and self- and cross-phase modulation (SPM, XPM). In this letter, we discuss an exact numerical model to calculate the spectral behaviour of RFLs and show its application to determine the effective reflectivity of the FBGs. The model is based on a combination of the nonlinear Schroedinger equation including dispersion, FWM, SPM, and XPM with a shooting method to solve the power steady-state equations for RFLs. Numerical results are in good agreement with measurements.     

Meat starters have individual requirements for Mn(2+)

The effect of different Mn(2+) concentrations on sausage fermentation was evaluated. A screening experiment was carried out with six lactobacilli starters in a sausage model. To further investigate the effects found, two selected lactobacilli strains were tested in pilot-scale sausage production. For all starters an increased fermentation rate was observed after Mn(2+) addition. Differences in the development of microbial, textural and sensory parameters were observed in the sausages. For one of the cultures these differences levelled out during sausage production yielding identical end products with and without Mn(2+), for the other strain the differences due to Mn(2+) addition in the sausages remained throughout the production process yielding sausages with different properties. Knowing a starter culture's requirements for Mn(2+) will allow optimisation of dry fermented sausage production in order to increase reliability and reproducibility of production decrease fermentation time and ensure microbial safety of the final product.     

Curing of Glycidyl Azide Polymer (GAP) Diol Using Isocyanate,Isocyanate‐Free,Synchronous Dual,and Sequential Dual Curing Systems

Glycidyl azide polymer (GAP) is an important energetic binder candidate for new minimum signature solid composite rocket propellants, but the mechanical properties of such GAP propellants are often limited. The mechanical characteristics of composite rocket propellants are mainly determined by the nature of the binder system and the binder‐filler interactions. In this work, we report a detailed investigation into curing systems for GAP diol with the objective of attaining the best possible mechanical characteristics as evaluated by uniaxial tensile testing of non‐plasticized polymer specimens. We started out by investigating isocyanate and isocyanate‐free curing systems, the latter by using the crystalline and easily soluble alkyne curing agent bispropargylhydroquinone (BPHQ). In the course of the presented study, we then assessed the feasibility of dual curing systems, either by using BPHQ and isophorone diisocyanate (IPDI) simultaneously (synchronous dual curing), or by applying propargyl alcohol and IPDI consecutively (sequential dual curing). The latter method, which employs propargyl alcohol as a readily available and adjustable hydroxyl‐telechelic branching agent for GAP through thermal triazole formation, gave rise to polymer specimens with mechanical characteristics that compared favorably with the best polymer specimens obtained from GAP diol and mixed isocyanate curatives. The glass transition temperature (T_g) of non‐plasticized samples was heightened when triazole‐based curing agents were included, but when plasticized with nitratoethylnitramine (NENA) plasticizer, T_g values were very similar, irrespective of the curing method.     

Gaussian profile estimation in one dimension

We present several new results on the classic problem of estimating Gaussian profile parameters from a set of noisy data, showing that an exact solution of the maximum likelihood equations exists for additive Gaussian-distributed noise. Using the exact solution makes it possible to obtain analytic formulas for the variances of the estimated parameters. Finally, we show that the classic formulation of the problem is actually biased, but that the bias can be eliminated by a straightforward algorithm.     

A New Total Flooding Test Procedure for Evaluating Fire-Suppressant Agents

A simple laboratory apparatus is described for observing the performance of fire extinguishing agents in total flooding applications. Known compositions of agents mixed with dry air are prepared in a 2 L glass combustion flask, and a flame fed by propane, butane, or other gaseous fuel from a pressure cylinder is inserted into the flask through a standard taper joint. Burning times to extinguishment are measured, both in the absence and presence of added physical or chemical agents. From the known rate of propane burning and initial compositions, the percentages of gas volume in the combustion flask at extinguishment are calculated for each burning time. Agents that are not sufficiently volatile to be investigated with the ordinary cup burner method are readily studied with the new technique.An adiabatic flame temperature model previously used to correlate cup burner test results has been applied to obtain limiting agent percentages required for total flooding extinguishment and to accurately predict the effect on burning time of different concentrations of physical and chemical agents and other gases in the flask.     

Random-phase-shift Fizeau interferometer

A new and potentially cost efficient kind of vibration-tolerant surface measurement interferometer based on the Fizeau-principle is demonstrated. The crucial novelty of this approach is the combination of two optoelectronic sensors: an image sensor with high spatial resolution and an arrangement of photodiodes with high temporal resolution. The photodiodes continuously measure the random-phase-shifts caused by environmental vibrations in three noncollinear points of the test surface. The high spatial resolution sensor takes several "frozen" images of the test surface by using short exposure times. Under the assumption of rigid body movement the continuously measured phase shifts of the three surface points enable the calculation of a virtual plane that is representative for the position and orientation of the whole test surface. For this purpose a new random-phase-shift algorithm had to be developed. The whole system was tested on an optical table without vibration isolation under the influence of random vibrations. The analysis of the root-mean-square (RMS) over ten different measurements shows a measurement repeatability of about 0.004 wave (approximately 2.5 nm for 632.8 nm laser wavelength).     

Compound prism design principles, II: triplet and Janssen prisms

Continuing the work of the first paper in this series [Appl. Opt. 50, 4998-5011 (2011)], we extend our design methods to compound prisms composed of three independent elements. The increased degrees of freedom of these asymmetric prisms allow designers to achieve greatly improved dispersion linearity. They also, however, require a more careful tailoring of the merit function to achieve design targets, and so we present several new operands for manipulating the compound prisms' design algorithm. We show that with asymmetric triplet prisms, one can linearize the angular dispersion such that the spectral sampling rate varies by no more than 4% across the entire visible spectral range. Doing this, however, requires large prisms and causes beam compression. By adding a beam compression penalty to the merit function, we show that one can compromise between dispersion linearity and beam compression in order to produce practical systems. For prisms that do not deviate the beam, we show that Janssen prisms provide a form that maintains the degrees of freedom of the triplet and that are capable of up to 32° of dispersion across the visible spectral range. Finally, in order to showcase some of the design flexibility of three-element prisms, we also show how to design for higher-order spectral dispersion to create a two-dimensional spectrum.     

Two-finger (TF) SPUDT cells

SPUDT cells including two fingers are only known thus far for so-called NSPUDT directions. In that case, usual solid-finger cells are used. The purpose of the present paper is to find SPUDT cell types consisting of two fingers only for pure mode directions. Two-finger (TF) cells for pure mode directions on substrates like 128°YX LiNbO(3) and YZ LiNbO(3) were found by means of an optimization procedure. The forward direction of a TF-cell SPUDT on 128°YX LiNbO(3) was determined experimentally. The properties of the new cells are compared with those of conventional SPUDT cells. The reflectivity of TF cells on 128°YX LiNbO(3) turns out to be two to three times larger than that of distributed acoustic reflection transducer (DART) and Hanma-Hunsinger cells at the same metal layer thickness.